mirror of
https://github.com/PentHertz/OpenBTS.git
synced 2026-05-14 16:40:12 +00:00
46a41b4a5c
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2305 19bc5d8c-e614-43d4-8b26-e1612bc8e597
85 lines
3.4 KiB
C
85 lines
3.4 KiB
C
/*
|
|
* Copyright 2011 Free Software Foundation, Inc.
|
|
*
|
|
*
|
|
* This software is distributed under the terms of the GNU Affero Public License.
|
|
* See the COPYING file in the main directory for details.
|
|
*
|
|
* This use of this software may be subject to additional restrictions.
|
|
* See the LEGAL file in the main directory for details.
|
|
|
|
This program is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU Affero General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
This program is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU Affero General Public License for more details.
|
|
|
|
You should have received a copy of the GNU Affero General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
|
|
*/
|
|
|
|
/*
|
|
* defines for the VRQ_SPI_READ and VRQ_SPI_WRITE commands
|
|
*
|
|
* SPI == "Serial Port Interface". SPI is a 3 wire bus plus a
|
|
* separate enable for each peripheral. The common lines are SCLK,
|
|
* SDI and SDO. The FX2 always drives SCLK and SDI, the clock and
|
|
* data lines from the FX2 to the peripheral. When enabled, a
|
|
* peripheral may drive SDO, the data line from the peripheral to the
|
|
* FX2.
|
|
*
|
|
* The SPI_READ and SPI_WRITE commands are formatted identically.
|
|
* Each specifies which peripherals to enable, whether the bits should
|
|
* be transmistted Most Significant Bit first or Least Significant Bit
|
|
* first, the number of bytes in the optional header, and the number
|
|
* of bytes to read or write in the body.
|
|
*
|
|
* The body is limited to 64 bytes. The optional header may contain
|
|
* 0, 1 or 2 bytes. For an SPI_WRITE, the header bytes are
|
|
* transmitted to the peripheral followed by the the body bytes. For
|
|
* an SPI_READ, the header bytes are transmitted to the peripheral,
|
|
* then len bytes are read back from the peripheral.
|
|
*/
|
|
|
|
/*
|
|
* SPI_FMT_* goes in wIndexL
|
|
*/
|
|
#define SPI_FMT_xSB_MASK (1 << 7)
|
|
# define SPI_FMT_LSB (1 << 7) // least signficant bit first
|
|
# define SPI_FMT_MSB (0 << 7) // most significant bit first
|
|
#define SPI_FMT_HDR_MASK (3 << 5)
|
|
# define SPI_FMT_HDR_0 (0 << 5) // 0 header bytes
|
|
# define SPI_FMT_HDR_1 (1 << 5) // 1 header byte
|
|
# define SPI_FMT_HDR_2 (2 << 5) // 2 header bytes
|
|
|
|
/*
|
|
* SPI_ENABLE_* goes in wIndexH
|
|
*
|
|
* For the software interface, the enables are active high.
|
|
* For reads, it's an error to have more than one enable set.
|
|
*
|
|
* [FWIW, the hardware implements them as active low. Don't change the
|
|
* definitions of these. They are related to usrp_rev1_regs.h]
|
|
*/
|
|
#define SPI_ENABLE_FPGA 0x01 // select FPGA
|
|
#define SPI_ENABLE_CODEC_A 0x02 // select AD9862 A
|
|
#define SPI_ENABLE_CODEC_B 0x04 // select AD9862 B
|
|
#define SPI_ENABLE_reserved 0x08
|
|
#define SPI_ENABLE_TX_A 0x10 // select d'board TX A
|
|
#define SPI_ENABLE_RX_A 0x20 // select d'board RX A
|
|
#define SPI_ENABLE_TX_B 0x40 // select d'board TX B
|
|
#define SPI_ENABLE_RX_B 0x80 // select d'board RX B
|
|
|
|
/*
|
|
* If there's one header byte, it goes in wValueL.
|
|
*
|
|
* If there are two header bytes, they go in wValueH | wValueL.
|
|
* The transmit order of the bytes (and bits within them) is
|
|
* determined by SPI_FMT_*SB
|
|
*/
|
|
|